- What is meant by stability and Q point?
- What is the difference between AC and DC load line?
- What is load line length?
- What are the markings on the side of a ship?
- Why BJT is called current controlled device?
- What is a DC load line?
- What is the difference between line and load?
- What is DC operating point of a transistor?
- What does bias mean?
- What are the two end points of the DC load line?
- What is quiescent point?
- What is the importance of load line?
- What is an AC load?
- What is the Q point of a diode?
- Why do ships have multiple load lines?
What is meant by stability and Q point?
This operating point is also called as quiescent point or simply Q-point.
The operating point should not get disturbed as it should remain stable to achieve faithful amplification.
Hence the quiescent point or Q-point is the value where the Faithful Amplification is achieved..
What is the difference between AC and DC load line?
If this load line is drawn only when DC biasing is given to the transistor, but no input signal is applied, then such a load line is called as DC load line. Whereas the load line drawn under the conditions when an input signal along with the DC voltages are applied, such a line is called as an AC load line.
What is load line length?
LOAD LINE LENGTH is defined as the greater of the following distances: The distance between the fore part of the stem to the aft and the axis of the rudder stock OR 96% of the distance between the fore side of the stem and the aft of the stern.
What are the markings on the side of a ship?
The Plimsoll line is a reference mark located on a ship’s hull that indicates the maximum depth to which the vessel may be safely immersed when loaded with cargo. This depth varies with a ship’s dimensions, type of cargo, time of year, and the water densities encountered in port and at sea.
Why BJT is called current controlled device?
BJT is a current controlled device because the output characteristics of BJT are determined by the input current. In a p-n junction i.e base-emitter junction in BJT the change in voltage (Vbe) is produced only after the change in base current.
What is a DC load line?
The DC load line is the load line of the DC equivalent circuit, defined by reducing the reactive components to zero (replacing capacitors by open circuits and inductors by short circuits). It is used to determine the correct DC operating point, often called the Q point.
What is the difference between line and load?
With the first device, the line is the wire running from the service panel to the device, and the load is the wire running from the first device to the second device downstream on the circuit. … The load side is where the power leaves the device (or electrical box) and travels down the circuit.
What is DC operating point of a transistor?
This calculates the DC operating point, also known as the bias point, of a circuit. This is the steady-state voltage or current at a specified pin of an active device with no input signal applied. When you run a DC operating point simulation, the results appear on the probes. …
What does bias mean?
Bias, prejudice mean a strong inclination of the mind or a preconceived opinion about something or someone. A bias may be favorable or unfavorable: bias in favor of or against an idea.
What are the two end points of the DC load line?
The load lines are obtained by joining the two points they are collector current (IC) and common emitter voltage (VCE).
What is quiescent point?
The operating point of a device, also known as bias point, quiescent point, or Q-point, is the DC voltage or current at a specified terminal of an active device (a transistor or vacuum tube) with no input signal applied. A bias circuit is a portion of the device’s circuit which supplies this steady current or voltage.
What is the importance of load line?
The purpose of the load line is to ensure that a ship has sufficient freeboard (the height from the waterline to the main deck) and thus sufficient reserve buoyancy (volume of ship above the waterline). It should also ensure adequate stability and avoid excessive stress on the ship’s hull as a result of overloading.
What is an AC load?
AC loads are devices which receives alternating-current (AC) electrical power from a source in an electrical system. A programmable AC load bank is commonly integrated into circuits for testing and measurement of current, voltage and frequency.
What is the Q point of a diode?
Q point or the operating point of a device, also known as a bias point, or quiescent point is the steady-state DC voltage or current at a specified terminal of an active device such as a diode or transistor with no input signal applied.
Why do ships have multiple load lines?
Multiple load lines are used when, for a period of time, a ship has a need to operate temporarily with a greater freeboard than the minimum freeboard stipulated in accordance with the International Convention on Load Lines of 1966.